commit fa00d6dc19283bee13f0390546f741293f6d2d9a upstream.

SCIF1 interface is available on PMOD1 connector (CN7) on carrier board.

This patch adds pinmux and scif1 node to carrier board dtsi file for
RZ/G2LC SMARC EVK.

Signed-off-by: Biju Das <biju.das.jz@...>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@...>
Link: https://lore.kernel.org/r/20220203170636.7747-4-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@...>
Signed-off-by: Biju Das <biju.das.jz@...>
---
.../dts/renesas/rzg2lc-smarc-pinfunction.dtsi | 7 +++++
arch/arm64/boot/dts/renesas/rzg2lc-smarc.dtsi | 26 +++++++++++++++++++
2 files changed, 33 insertions(+)

diff --git a/arch/arm64/boot/dts/renesas/rzg2lc-smarc-pinfunction.dtsi b/arch/arm64/boot/dts/renesas/rzg2lc-smarc-pinfunction.dtsi
index 1032f6563515..ec9e08ec0822 100644
--- a/arch/arm64/boot/dts/renesas/rzg2lc-smarc-pinfunction.dtsi
+++ b/arch/arm64/boot/dts/renesas/rzg2lc-smarc-pinfunction.dtsi
@@ -17,6 +17,13 @@ scif0_pins: scif0 {
<RZG2L_PORT_PINMUX(38, 1, 1)>; /* RxD */
};

+ scif1_pins: scif1 {
+ pinmux = <RZG2L_PORT_PINMUX(40, 0, 1)>, /* TxD */
+ <RZG2L_PORT_PINMUX(40, 1, 1)>, /* RxD */
+ <RZG2L_PORT_PINMUX(41, 0, 1)>, /* CTS# */
+ <RZG2L_PORT_PINMUX(41, 1, 1)>; /* RTS# */
+ };
+
sd1-pwr-en-hog {
gpio-hog;
gpios = <RZG2L_GPIO(39, 2) GPIO_ACTIVE_HIGH>;
diff --git a/arch/arm64/boot/dts/renesas/rzg2lc-smarc.dtsi b/arch/arm64/boot/dts/renesas/rzg2lc-smarc.dtsi
index ca5ca7ce6692..1b59ef376296 100644
--- a/arch/arm64/boot/dts/renesas/rzg2lc-smarc.dtsi
+++ b/arch/arm64/boot/dts/renesas/rzg2lc-smarc.dtsi
@@ -34,3 +34,29 @@
#include "rzg2lc-smarc-som.dtsi"
#include "rzg2lc-smarc-pinfunction.dtsi"
#include "rz-smarc-common.dtsi"
+
+/* comment the #define statement to disable SCIF1 (SER0) on PMOD1 (CN7) */
+#define PMOD1_SER0 1
+
+/ {
+ aliases {
+ serial1 = &scif1;
+ };
+};
+
+/*
+ * To enable SCIF1 (SER0) on PMOD1 (CN7), On connector board
+ * SW1 should be at position 2->3 so that SER0_CTS# line is activated
+ * SW2 should be at position 2->3 so that SER0_TX line is activated
+ * SW3 should be at position 2->3 so that SER0_RX line is activated
+ * SW4 should be at position 2->3 so that SER0_RTS# line is activated
+ */
+#if (!SW_SCIF_CAN && PMOD1_SER0)
+&scif1 {
+ pinctrl-0 = <&scif1_pins>;
+ pinctrl-names = "default";
+
+ uart-has-rtscts;
+ status = "okay";
+};
+#endif
--
2.25.1